Design of the Hoisting System for D-Zero Collision Hall Pit
Notice bibliographique
Résumé
A hoisting rail system has been designed for lifting loads from the north sidewalk of the D0 collision hall into the collision hall pit. This engineering note documents the design. The hoisting system was conceived primarily to aid in getting heavy loads into the pit during short (less than a few days) accesses. The typical use for the hoist will be to lift a BLS power supply (120 lbs) and carrier (16 lbs) from a roll around cart on the sidewalk and onto a similar cart in the collision hall pit. The hoist system will alleviate the need for two persons to carry this heavy load up and down a narrow (24-inch) staircase. The hoisting system has a designed lift rating of 150 lbs. All members and components are well within a conservative safety factor when subjected to this loading at it's worst possible configuration, that is with it's boom cantilevered out 8 feet from the base rail. See the hoisting rail assembly sketch (in the hand calculations section) and the picture inserted below to get an orientation of the device. The hoisting system is designed using BLine 'unistrut' system components. The hoist consists of a 'base' rail that is fastened to either the northeast or northwest air handler platforms. This fixed base rail has (2) two sided trolley assemblies inserted into it's lower unistrut member. One assembly is locked in place on the base rail. Another is locked in place on the lower 'boom' rail. The trolley assemblies are free wheeling which allows boom movement in the north-south direction about 7 1/2 feet within the fixed base rail. An electric hoist hangs from the 'boom' rail on a single trolley. The hoisting system meets Fermilab Environment and Safety Manual chapter 5021 entitled 'Overhead cranes hoists and rigging'. Inclusive in that requirement is that it meets the applicable Fermilab 'work smart standards' of ANSI B30.11-1998 'Monorails and underhung cranes', and ANSI B30.16-1998 'Overhead hoists (underhung)'. The design criteria for the structural members per these standards is that static stresses shall not exceed 0.2 times the average ultimate material strength. The unistrut members are fabricated from hot rolled carbon steel. The B-Line catalog states that the minimum yield strength of the virgin material is 33,000 psi and the cold worked average yield stress is 42,000 psi. The ultimate strength of the material is not given in the catalog, but based on the description of the material and values listed in the Ryerson steel catalog, I will use a value 58,000 psi for the ultimate strength. A minimum safety factor of 5 must be achieved based on ultimate strength.
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Comment cette classification a été obtenuedéplier
Prédiction distillée sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.
Scores Codex et Gemma par catégorie
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,000 | 0,000 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,000 | 0,000 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,000 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,000 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découleClassification
machine, non validéePrédiction automatique; un appel candidat d’une seule tête enseignante, pas un consensus.
Le détail, modèle par modèle et score par score, se trouve en fin de page sous « Comment cette classification a été obtenue ».