The Influence of Pt Loading, Support and Nafion Content on the Performance of Direct Methanol Fuel Cells: Examined on the Example of the Cathode
Pourquoi ce travail est dans la base
Une base qui oublie comment elle a trouvé un travail ne peut pas être vérifiée. Voici les voies qui ont admis celui-ci.
Notice bibliographique
Résumé
Abstract Nano‐sized Pt colloids were prepared using the polyol method and supported on Ketjen black EC 600J (KB), Vulcan XC‐72 (VC) and high surface area graphite 300 (HG). The effects of the Nafion ionomer content, and the Pt loading of the cathode catalyst layer as well as the Pt loading on the support on the performance of direct methanol fuel cells (DMFCs), were studied. The membrane electrode assemblies (MEAs) were analysed using current–voltage curves, cyclic voltammetry, electrochemical impedance spectroscopy (EIS) and adsorbed CO stripping voltammetry. Optimum Nafion to carbon (N/C) ratios (N/C being defined as the weight ratio of the Nafion ionomer to the carbon) were determined. The optimum N/C ratios were found to depend on the support as follows, 1.4, 0.7 and 0.5 for Pt/KB, Pt/VC and Pt/HG, respectively and to be independent of the Pt/C loading range of 20–80 wt% tested in this work. The highest DMFC performances, as well as the highest electrochemical active surface areas, and improved gas diffusivities, were achieved using these ratios. For the catalysts prepared in this work, the average Pt crystallite size was found to decrease with increasing surface area of the support for a particular Pt loading. MEAs made using KB as support and the optimal N/C ratio of 1.4 showed the best performances, i.e. higher than the VC and HG supports for any N/C ratio. The highest DMFC performance was observed using 60 wt% Pt on KB cathode electrodes of 1 mg Pt cm –2 loading and an N/C value of 1.4. For all three supports studied, the 60 wt% Pt on carbon loading resulted in the best DMFC performance. This may be linked to the Pt particle size and catalyst preparation method used in this work. In comparison to literature results, high DMFC performances were achieved using relatively ‘low' Pt and Ru loadings. For example, a maximum power density of >100 mW cm –2 at 60 °C was observed using a 1 mg Pt cm –2 cathode loading and a 2 mg PtRu cm –2 anode loading.
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Prédiction distillée sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.
Scores Codex et Gemma par catégorie
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,001 | 0,000 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,000 | 0,000 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,000 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,000 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découle