Physical and mechanical properties of pultruded composites containing fillers and low profile additives
Pourquoi ce travail est dans la base
Une base qui oublie comment elle a trouvé un travail ne peut pas être vérifiée. Voici les voies qui ont admis celui-ci.
Notice bibliographique
Résumé
Abstract This article deals with the effect of fillers and additives content on the physical and mechanical properties of unidirectional pultruded glass/polyester composites. The physical characterization consisted of determining the void volume fraction (Vv), density, shrinkage ratio, coefficient of thermal expansion (CTE), and dynamic mechanical properties. The mechanical tests consisted of three‐point‐bending tests under static, impact, and fatigue loading. The low profile additive (LPA) has been found to compensate the cure shrinkage by microvoid formation. Dynamic mechanical analysis measurements show that the LPA slightly lowers the glass transition temperature Tg and increases the internal damping Tan δ. The transverse coefficient of thermal expansion was found to be sensitive to the LPA content. Three‐point bending tests show that the interlaminar shear strength (ILSS) is slightly sensitive to the fillers and LPA content, but the flexural strength is not affected. Impact test results on short beam shear and flexural specimens show the same behavior as in the static tests except that the LPA content has a detrimental effect on the flexural impact properties. The fatigue tests performed show that the effect of fillers is not significant, while the LPA effect is mixed. It seems that there is an LPA content for which the fatigue resistance is maximized. Finally, the wide range of behaviors and span‐to‐depth ratios investigated suggest that the ILSS as measured according to the ASTM 2344 recommendations can be largely misleading because of the unavoidable compressive yielding under the loading nose. For the materials investigated, higher span‐to‐depth ratio are more representative of the ILSS. POLYM. COMPOS., 27:71–81, 2006. © 2005 Society of Plastics Engineers
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Prédiction distillée sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.
Scores Codex et Gemma par catégorie
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,000 | 0,000 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,000 | 0,000 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,000 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,000 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découle