An Experimental Study of Saturated and Unsaturated Permeabilities in Resin Transfer Molding Based on Unidirectional Flow Measurements
Pourquoi ce travail est dans la base
Une base qui oublie comment elle a trouvé un travail ne peut pas être vérifiée. Voici les voies qui ont admis celui-ci.
Notice bibliographique
Résumé
Resin transfer molding (RTM) is a manufacturing process of composite parts that consists of injecting a fluid resin through a fibrous reinforcement. Permeability of the fiber bed is a key parameter that governs the flow, together with the viscosity of the resin. In this paper, the saturated and unsaturated permeabilities of a glass-woven fabric are studied for different injection pressures and porosities of the fibrous reinforcement. Unidirectional injection experiments are carried out to evaluate the unsaturated permeability of the reinforcement during the injection and the saturated permeability that governs the permanent flow established after filling of the cavity. The unsaturated permeability is evaluated by a linear regression in function of the position of the resin front during transient flow experiments performed at constant injection pressure. For each position of the resin front in the test mold, a transient permeability can be calculated by application of Darcy’s law. This transient permeability depends on the injection pressure, position of the resin front in the mold, and porosity of the reinforcement. After a certain flow length called the convergence length, the transient permeability converges to a value that is independent of the flow rate and of the injection pressure. This limit value is called here the unsaturated permeability. The convergence length is related to a maximum flow rate or average particle velocity below which Darcy’s law holds. The saturated permeability is measured after all air bubbles have been evacuated from the cavity. As a result of this experimental investigation, three parameters can be identified that are characteristic of the pore structure of the fibrous reinforcement: (1) a maximum average resin velocity can be identified below which the transient permeability remains constant; (2) the saturated and unsaturated permeabilities differ by a value that remains constant within the injection pressure range used in this study and that is independent of the fiber volume content; (3) the new notion of convergence length proposed here, namely the flow length necessary to ensure convergence of the transient permeability, depends on the two-scale pore structure of the fibrous reinforcement. This study corroborates the findings of several other investigators, who have shown that the saturated permeability is always higher than the unsaturated permeability. The difference between these two permeability values is also related to the pore structure of the fiber bed. It is hoped that this work will contribute to define a much-needed standard on permeability measurements.
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Prédiction distillée sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.
Scores Codex et Gemma par catégorie
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,000 | 0,000 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,000 | 0,000 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,000 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,000 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découle