MétaCan
Menu
Retour à la cohorte
Enregistrement W2326971961 · doi:10.2118/178441-ms

Sand Control Screen Cyclic Thermal Testing for Life of SAGD Wells

2015· article· en· W2326971961 sur OpenAlexaffabout
Ma Guobin, Shaelyn M Gordon, Adil Arshad, Marc R Carriere, Jamie L Olson, Kirk L. Hamilton, Mark Droessler, Thomas Dessein

Notice bibliographique

RevueSPE Thermal Well Integrity and Design Symposium · 2015
Typearticle
Langueen
DomaineEngineering
ThématiqueDrilling and Well Engineering
Établissements canadiensBaker Hughes (Canada)
Organismes subventionnairesBaker Hughes
Mots-clésFinite element methodThermalCoiled tubingStructural engineeringMaterials sciencePetroleum engineeringEngineering

Résumé

récupéré en direct d'OpenAlex

Abstract Wire Wrapped Screens (WWS) have received more attention from Steam assisted Gravity Drainage (SAGD) operators. A WWS is commonly fabricated with a wedge-shaped wire that is spiral-wound around a perforated base pipe to form a Wire wound Mesh (WWM). This produces a single, continuous, keystone-shaped helical slot with a large open flow area to enable for fluid flow while maintaining the structural rigidity of the base pipe and providing sand control to the wellbore. The structural integrity of a WWS with dual ring Wrap-On-Pipe (WOP) WWM and gap opening and closing within the WWM during thermally-induced loading were assessed through a full-scale thermal test program and Finite Element Analysis (FEA), during which the WWS was subjected to thermal cycle loading between 20°C (68°F) (room temperature) and 280°C (536°F), simulating the target temperature of a relatively high-temperature SAGD project in northern Alberta. The loading condition selected as the worst-case scenario from a service limit state perspective for the testing and FEA was to enable the WWS specimens to freely expand during the initial heating phase and then axially constrain them for the subsequent thermal cycle loading. This loading condition was selected because it was the scenario most likely to cause gap width opening between the wire wraps to an extent where the WWS could no longer provide suitable sand exclusion. The FEA was used to determine the peak plastic strains within the base pipe and the effect that the residual stresses, introduced by the welding process, have on the structural integrity of the WWS. The frictional conditions between the spiral-wound wire and base pipe were found to have a significant impact on limiting axial movement between the WWM and base pipe, and the axial strains developed in the screen. In addition, an analytical model is presented that estimates the gap opening of the WWM because of thermal strains, which compared well to the results obtained through FEA. The testing was conducted to assess the structural capacity of the WWS design and monitor change in gap widths during thermal cycling at key structural locations of the WWS design. The strain monitoring results from the full-scale test program were found to be consistent with the predicted strains from the FEA assessment. This paper presents testing and FEA results for a WWS with WOP WWM, and investigates the potential of a WWS to provide long-term and reliable sand control for SAGD wells.

Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.

Comment cette classification a été obtenuedéplier

Prédiction distillée sur la base complète

Imitation des enseignants

Ni prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.

score de la tête « metaresearch » (Codex)0,001
score de la tête « metaresearch » (Gemma)0,000
Version: codex-gemma-dda1882f352aStatut de validation: machine_predicted_unvalidated
Catégories candidatesMéta-épidémiologie (sens strict)
Catégories consensuellesaucune
DomaineSignal candidat: aucune · Signal consensuel: aucune
Devis d'étudeSignal candidat: Simulation ou modélisation · Signal consensuel: Simulation ou modélisation
GenreSignal candidat: Empirique · Signal consensuel: aucune
Score de désaccord entre enseignants0,774
Score d'incertitude au seuil1,000

Scores Codex et Gemma par catégorie

CatégorieCodexGemma
Métarecherche0,0010,000
Méta-épidémiologie (sens strict)0,0000,000
Méta-épidémiologie (sens large)0,0000,000
Bibliométrie0,0000,000
Études des sciences et des technologies0,0000,000
Communication savante0,0000,000
Science ouverte0,0000,000
Intégrité de la recherche0,0000,000
Charge utile insuffisante (le modèle a refusé de juger)0,0000,000

Scores machine (provisoires)

Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.

Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.

Tête enseignante Opus0,038
Tête enseignante GPT0,226
Écart entre enseignants0,189 · la distance entre les deux têtes enseignantes sur ce seul travail
Statut de validationscore_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découle

Classification

machine, non validée

Prédiction automatique; un appel candidat d’une seule tête enseignante, pas un consensus.

Devis d'étudeSimulation ou modélisation
Domainenon disponible
GenreEmpirique

Le détail, modèle par modèle et score par score, se trouve en fin de page sous « Comment cette classification a été obtenue ».

En bref

Citations3
Publié2015
Routes d'admission2
Résumé présentoui

Explorer davantage

Même revueSPE Thermal Well Integrity and Design SymposiumMême sujetDrilling and Well EngineeringTravaux en français237 207