Significance of HAZ Softening on Strain Concentration and Crack Driving Force in Pipeline Girth Welds
Notice bibliographique
Résumé
Modern micro-alloyed, control-rolled TMCP steels generally have good strength, high toughness, and good weldability. However, these valuable properties come along with certain undesirable features, such as low strain hardening (high yield to tensile ratio), low ductility as measured by uniform elongation (elongation at ultimate tensile strength), and possible heat-affect-zone (HAZ) softening due to reduced hardenability. These undesirable features are particularly detrimental in strain-based design of pipelines. Although the phenomenon of HAZ softening has been known for a long time, the impact of the HAZ softening on the integrity of pipeline girth welds was not well understood. The objective of this work was to understand the impact of HAZ softening on girth weld integrity. Finite element analysis was conducted to investigate the effects of HAZ softening on crack driving force and strain concentration in girth welds under longitudinal tensile loading. The material properties of WM and BM were obtained from an X100 girth weld. The HAZ was modeled as a functionally graded material based on its measured hardness. The models contained surface-breaking defects located at the fusion boundary simulating lack-of-sidewall fusion defects. The analysis results showed that increased CTOD driving force can be expected due to HAZ softening. The extent of increase is positively related to the width and degree of softening of the HAZ. On the other hand, weld strength overmatch reduces the total CTOD driving force. The strain concentration in the softened HAZ circumferentially remote from a surface-breaking defect was small. However, high strain concentration existed over the circumference covering the length of the defect. This concentration was primarily attributable to the existence of the defect and secondarily to the HAZ softening. One significant result from this work was that the relative increase in CTOD driving force and strain concentration due to HAZ softening was independent of defect size. In other words, on a relative basis, HAZ softening was no worse on large defects than on smaller defects. This result should be helpful in rationalizing the effects of HAZ softening for defects of various sizes that exist in field applications. Non-symmetrical crack-tip deformation occurred with softened HAZ. A large proportion of the crack-tip deformation was located in the HAZ. The magnitude of non-symmetric deformation increased with the increase of HAZ width and degree of softening. Even higher degree of non-symmetric deformation occurred with the increase of weld overmatching level. The structural significance of reduced total CTOD driving force and increased un-symmetric deformation at the crack tip due to weld strength overmatch warrants further study. The reduction in total CTOD driving force alone does not necessarily results in a higher level of weld integrity if the “intrinsic” toughness of the HAZ is substantially lower than the weld metal.
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Comment cette classification a été obtenuedéplier
Prédiction distillée sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.
Scores Codex et Gemma par catégorie
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,000 | 0,000 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,000 | 0,000 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,000 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,000 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découleClassification
machine, non validéePrédiction automatique; un appel candidat d’une seule tête enseignante, pas un consensus.
Le détail, modèle par modèle et score par score, se trouve en fin de page sous « Comment cette classification a été obtenue ».