Application of Multiphase Flow Methods to Horizontal Underbalanced Drilling
Notice bibliographique
Résumé
Abstract Multiphase flow can be present in all aspects of underbalanced drilling. This paper outlines the ways in which multiphase flow pressure loss calculations can be used by drilling engineers in the design and optimization of underbalanced drilling operations. Then, detailed field measurements for several horizontal wells drilled underbalanced with coiled tubing are used to evaluate the application of existing pressure loss calculation methods to this unique application. Introduction Underbalanced drilling (UBD) is rapidly gaining popularity in the oil and gas industry. The Alberta Energy and Utilities Board ID94–3(1) defines underbalanced drilling as follows: "When the hydrostatic head of a drilling fluid is intentionally designed to be lower than the pressure of the formation being drilled, the operation will be considered underbalanced drilling. The hydrostatic head of the drilling fluid may be naturally less than the formation pressure or it can be induced. The induced state may be created by adding natural gas, nitrogen, or air to the liquid phase of the drilling fluid. Whether induced or natural, this may result in an influx of formation fluid which must be circulated from the well and controlled at surface." Benefits of Underbalanced Drilling Maintaining the pressure in the wellbore below the reservoir pressure allows reservoir fluids to enter the wellbore while UBD operations proceed, thus preventing flow of drilling fluids (and associated solids) into the formation, thereby minimizing or even eliminating formation damage. This is of particular importance in the drilling of horizontal wells as the formation is exposed to the drilling fluids for an extended period of time. Although formation damage reduction is the most widely recognized benefit of underbalanced drilling, several additional benefits are outlined below: Increased Penetration Rates Underbalanced drilling can achieve higher rates of penetration due to reduced "chip holdown" and decreased hydrostatic pressure at the bit face. Reduction in "chip holdown" refers to easier removal of drilled solids from the vicinity of the drill bit due to the flow of drilling and reservoir fluids, thus allowing the bit to drill into fresh rock continuously. The decreased hydrostatic pressure at the bit face reduces stress in the rock being drilled, allowing it to fail more easily. The experience of drilling engineers(2) familiar with UBD is that the rate of penetration can be increased by between three and ten times that of conventional drilling. Minimal Lost Circulation Underbalanced drilling gives better control in situations where fractured, low pressure, or high permeability formations may lead to the loss of drilling fluids and the associated problems that can cause. Evaluation While Drilling Data acquired in real time during underbalanced drilling operations allow for both the short term on site optimization of the UBD operation, and the longer term assessment of the well's potential. On site, the data acquired can be used to optimize drilling parameters such as the well's horizontal length, vertical depth, and orientation. Other data that can be obtained, useful both on site and long term, include fluid properties, productivity, and geological interpretations of the formation.
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Comment cette classification a été obtenuedéplier
Prédiction machine sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Le volet Gemma est une étiquette directe du modèle pour chaque travail de la base, lue sur la notice réduite au titre. Le volet Codex est un classifieur appris des 10 348 étiquettes directes de Codex et calibré sur les taux pondérés de l'échantillon; les champs sans appui suffisant ne portent aucun appel Codex. Le mode candidate est l'union des deux volets; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont pas des étiquettes humaines.
Scores du classifieur distillé par catégorie (deux têtes)
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,001 | 0,001 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,001 | 0,000 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,001 | 0,001 |
| Science ouverte | 0,001 | 0,001 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,001 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découleClassification
machine, non validéePrédiction automatique; un appel candidat d’une seule source (Gemma direct ou Codex distillé), pas un consensus.
Le détail, modèle par modèle et score par score, se trouve en fin de page sous « Comment cette classification a été obtenue ».