Water Permeability Reduction Under Flow-Induced Polymer Adsorption
Pourquoi ce travail est dans la base
Une base qui oublie comment elle a trouvé un travail ne peut pas être vérifiée. Voici les voies qui ont admis celui-ci.
Notice bibliographique
Résumé
Abstract The influence of induced polymer adsorption for reducing the effective permeability to water in reservoirs is investigated. Previous studies on polymer adsorption in porous media have shown that static adsorption regime exists at low shear rate of injection. This results in thin polymer layer whose capability to reduce water permeability is marginal. However, polymer injection at increasing shear rates has revealed an increase in the adsorbed polymer layer and consequently, improved water permeability reduction. In this work, experimental results from sandpacks were presented to show that at increased shear rates, there is improvement in the adsorbed polymer layer. This phenomenon is known as "flow-induced adsorption". The experiments indicate that above a critical shear rate, there is a shift in permeability-reduction-mechanism from static adsorption to flow-induced adsorption, necessitating a sharp increase in adsorbed polymer layer. All the experimental results revealed that the critical shear rate for this polymer is about 300s-1 in the absence of mechanical degradation. This critical shear rate defines the optimal rate of polymer injection for better economic viability of the process. Introduction and Background Increased water production with produced oil is a growing concern in the petroleum industry. The breakthrough of either formation or injected water, results in accelerated decline in oil production, increased operational cost of pumping, treatment and disposal of produced water. The need to curtail excess water production without affecting oil production has led to the use of polymers to reduce the permeability to water much more than the permeability to oil. This is essential in wells where water and oil is being produced from the same zone; hence, the water-bearing zones cannot easily be isolated. In many cases, direct injection of polymers in production wells has proven to be an efficient method to prevent excessive water production (1)(2). To understand the mechanisms that enable water permeability reduction, many experimental studies have investigated the resulting effect of polymer injection on two-phase flow in porous media (3)(4)(5)(6). All the studies indicate a selective action of the polymer with a significant reduction in the relative permeability to water with respect to the relative permeability to oil. Based on the fact that the wall effect is the dominant action of the polymer, polymer adsorption thus, plays a significant role in relative permeability modification, resulting in permeability reduction of porous media. The objective of polymer adsorption in production wells is to reduce water production without damaging oil productivity. This is critical to the success of near-wellbore conformance treatments in production wells if thehydrocarbon-productive zones cannot be protected during placement (7). Results of field treatments have varied widely, but often no obvious reason can be given for the success or failure of the treatment. The extent to which relative permeability is modified is governed by the degree of polymer adsorption within the porous medium under consideration. Zitha et al. (1995) reported that polymers are widely used for nearwellbore conformance control treatments to correct the permeability contrast between the layers.
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Prédiction distillée sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.
Scores Codex et Gemma par catégorie
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,000 | 0,000 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,000 | 0,000 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,000 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,001 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découle