Optimization of the Horizontal-Well Hydraulic-Fracture Geometry From Caprock-Integrity Point of View Using Fully Coupled 3D Cohesive Elements
Pourquoi ce travail est dans la base
Une base qui oublie comment elle a trouvé un travail ne peut pas être vérifiée. Voici les voies qui ont admis celui-ci.
Notice bibliographique
Résumé
Summary Pre-analysis of the geometry of a hydraulically induced fracture, including fracture width, length, and height, plays a crucial role in a successful hydraulic-fracturing (HF) operation. Besides the geometry of the fracture, the injection rate should be optimal for obtaining desired results such as maintaining sufficient aperture for proppant placement, avoiding screenouts or proppant bridging, and also preventing caprock-integrity failure as a result of an extensively uncontrolled fracture in reservoirs. A sophisticated numerical model derived from the cohesive-elements method has been developed and validated using field data to obtain an insight on the optimal fracture geometry and injection rate that can lead to a safe and efficient operation. The HF operation has been conducted in an oil field in the Persian Gulf with the aim of enhanced oil recovery (EOR) from a limestone reservoir with low matrix permeability in a horizontal wellbore. The concept of the cohesive-elements method with pore pressure as an additional degree of freedom has been applied to a 3D fully coupled HF model to estimate fracture geometry, specifically fracture height as a function of the optimal injection rate in a reservoir porous medium. It was observed that by increasing injection rate, all the fracture-geometry parameters steeply increased, but the fracture height must be controlled to be in the reservoir domain and not surpass the caprock and sublayer. For the reservoir under study with the maximum height of 100 m, length of 250 m, width of 100 m, permeability of 2 md, and porosity of 10%, the optimal fracture height is 73.4 m; the average fracture width and half-length are 12.8 mm and 55.4 m, respectively. Therefore, the optimal injection rate derived from the fracture height and geometry is in this case 4.5 bbl/min. The computed fracture pressure (49.55 MPa = 7,283.85 psi) has been compared with the field fracture pressure (51.02 MPa = 7,500 psi), and the error obtained for these two values is 2.88%, which showed a very good agreement.
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Prédiction distillée sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.
Scores Codex et Gemma par catégorie
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,000 | 0,000 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,000 | 0,000 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,000 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,000 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découle