MétaCan
Menu
Retour à la cohorte
Enregistrement W3005340033 · doi:10.2118/199247-ms

Challenges and Potentials for Sand Control Design and Management in Oil Reservoirs of Kazakhstan

2020· article· en· W3005340033 sur OpenAlexaff
Mohammad Soroush, Seyed Abolhassan Hosseini, Morteza Roostaei, Peyman Pourafshary, Mahdi Mahmoudi, Ali Ghalambor, Vahidoddin Fattahpour

Notice bibliographique

RevueSPE International Conference and Exhibition on Formation Damage Control · 2020
Typearticle
Langueen
DomaineEngineering
ThématiqueHydraulic Fracturing and Reservoir Analysis
Établissements canadiensUniversity of Alberta
Organismes subventionnairesnon disponible
Mots-clésGeologyTectonicsOil reservesInflowPetroleum engineeringPermeability (electromagnetism)Fossil fuelPorosityPetroleumGeotechnical engineeringGeochemistryOceanographyPaleontologyEngineering

Résumé

récupéré en direct d'OpenAlex

Abstract Kazakhstan owns one of the largest global oil reserves (~3%). This paper aims at investigating the challenges and potentials for production from weakly-consolidated and unconsolidated oil sandstone reserves in Kazakhstan. We used the published information in the literature, especially those including comparative studies between Kazakhstan and North America. Weakly consolidated and unconsolidated oil reserves, in Kazakhstan, were studied in terms of the depth, pay-zone thickness, viscosity, particle size distribution, clay content, porosity, permeability, gas cap, bottom water, mineralogy, solution gas, oil saturation, and homogeneity of the pay zone. The previous and current experiences in developing these reserves were outlined. The stress condition was also discussed. Furthermore, geological condition, including the existing structures, layers and formations were addressed for different reserves. Weakly consolidated heavy oil reserves in shallow depths (less than 500 m) with oil viscosity around 500 cP and thin pay zones (less than 10 m) have been successfully produced using cold methods, however, thicker zones could be produced using thermal options. Sand management is the main challenge in cold operations, while sand control is the main challenge in thermal operations. Tectonic history is more critical in comparison to the similar cases in North America. The complicated tectonic history, necessitates the geomechanical models to strategize the sand control especially in cased and perforated completion. These models are usually avoided in North America due to the less problematic conditions. Further investigation has shown that Inflow Control Devices (ICDs) could be utilized to limit the water breakthrough, as water coning is a common problem, which initiates and intensifies the sanding. This paper provides a review on challenges and potentials for sand control and sand management in heavy oil reserves of Kazakhstan, which could be used as a guideline for service companies and operators. This paper could be also used as an initial step for further investigations regarding the sand control and sand management in Kazakhstan.

Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.

Comment cette classification a été obtenuedéplier

Prédiction distillée sur la base complète

Imitation des enseignants

Ni prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.

score de la tête « metaresearch » (Codex)0,000
score de la tête « metaresearch » (Gemma)0,000
Version: codex-gemma-dda1882f352aStatut de validation: machine_predicted_unvalidated
Catégories candidatesaucune
Catégories consensuellesaucune
DomaineSignal candidat: aucune · Signal consensuel: aucune
Devis d'étudeSignal candidat: Simulation ou modélisation · Signal consensuel: aucune
GenreSignal candidat: Empirique · Signal consensuel: aucune
Score de désaccord entre enseignants0,835
Score d'incertitude au seuil0,415

Scores Codex et Gemma par catégorie

CatégorieCodexGemma
Métarecherche0,0000,000
Méta-épidémiologie (sens strict)0,0000,000
Méta-épidémiologie (sens large)0,0000,000
Bibliométrie0,0000,000
Études des sciences et des technologies0,0000,000
Communication savante0,0000,000
Science ouverte0,0000,000
Intégrité de la recherche0,0000,000
Charge utile insuffisante (le modèle a refusé de juger)0,0000,000

Scores machine (provisoires)

Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.

Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.

Tête enseignante Opus0,038
Tête enseignante GPT0,255
Écart entre enseignants0,216 · la distance entre les deux têtes enseignantes sur ce seul travail
Statut de validationscore_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découle

Classification

machine, non validée

Prédiction automatique; un appel candidat d’une seule tête enseignante, pas un consensus.

Les modèles n’ont appliqué aucune catégorie : rien dans la taxonomie ne correspondait à ce travail.
Devis d'étudeSimulation ou modélisation
Domainenon disponible
GenreEmpirique

Le détail, modèle par modèle et score par score, se trouve en fin de page sous « Comment cette classification a été obtenue ».

En bref

Citations1
Publié2020
Routes d'admission1
Résumé présentoui

Explorer davantage

Même revueSPE International Conference and Exhibition on Formation Damage ControlMême sujetHydraulic Fracturing and Reservoir AnalysisTravaux en français237 207