MétaCan
Menu
Retour à la cohorte
Enregistrement W3009034069 · doi:10.2118/199678-ms

Analysis of Torsional Stick-Slip Situations Observed with Downhole High-Frequency Magnetometer Data

2020· article· en· W3009034069 sur OpenAlexaff
Eric Cayeux, Adrian Ambrus, Lars Øy, Arvid Helleland, Svein Tore Brundtland, Harald Nevøy

Notice bibliographique

RevueIADC/SPE International Drilling Conference and Exhibition · 2020
Typearticle
Langueen
DomaineEngineering
ThématiqueDrilling and Well Engineering
Établissements canadiensConocoPhillips (Canada)
Organismes subventionnairesnon disponible
Mots-clésDrill stringRotational speedBoreholeSlip (aerodynamics)Drill pipeMechanicsDrillGeologyAcousticsEngineeringGeotechnical engineeringPhysicsMechanical engineering

Résumé

récupéré en direct d'OpenAlex

Abstract The use of downhole rotational speed measurements made at 300Hz gives new insight into the conditions under which stick-slip torsional oscillations occur. Observations made with high-frequency magnetometers while drilling two reservoir sections have shown, that for these wellbores, using top-drive speeds below 140rpm leads to severe downhole torsional oscillations, also in off-bottom conditions. Additionally, it was observed that downlinking the rotary steerable system (RSS) initiated heavy stick-slip and that reaming downward had a negative damping effect on downhole torsional stability. These observations have been compared and partly matched with estimations made with a transient hydro-mechanical model. Some ill-defined information had to be estimated, like the amount of flow diversion during the downlinking procedure, the coefficients of static and kinetic friction along the borehole, or the bit efficiency and aggressivity. Downhole measurements have shown that when the drill-string is subject to strong stick-slip conditions, the downhole rotational speed changes from stationary to more than 400rpm in just a fraction of a second. It is therefore important to utilize sampling rates that are compatible with such very fast events. In practice, that means several hundred Hertz. A challenge associated with analysis of downhole high frequency data is time synchronization and drift of clocks between the surface and downhole measurements. After time synchronization and correction, it appears that the downhole rotational movement is delayed by several tens of seconds compared to the actual top-drive speed. This leads to question whether rotating the drill-string off-bottom, typically done in order to break gelled-up mud prior to establishing circulation, has any significant the intended effects deviated wells as torque along the drill-string must be built up. Direct observations of downhole rotational speed at high frequency help in discovering conditions that were not suspected to lead to large torsional oscillations. This new information can be used to improve drilling operational procedures and models of the drilling process, therefore enabling increased drilling efficiency.

Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.

Comment cette classification a été obtenuedéplier

Prédiction distillée sur la base complète

Imitation des enseignants

Ni prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.

score de la tête « metaresearch » (Codex)0,000
score de la tête « metaresearch » (Gemma)0,000
Version: codex-gemma-dda1882f352aStatut de validation: machine_predicted_unvalidated
Catégories candidatesaucune
Catégories consensuellesaucune
DomaineSignal candidat: aucune · Signal consensuel: aucune
Devis d'étudeSignal candidat: Simulation ou modélisation · Signal consensuel: Simulation ou modélisation
GenreSignal candidat: Empirique · Signal consensuel: Empirique
Score de désaccord entre enseignants0,418
Score d'incertitude au seuil0,634

Scores Codex et Gemma par catégorie

CatégorieCodexGemma
Métarecherche0,0000,000
Méta-épidémiologie (sens strict)0,0000,000
Méta-épidémiologie (sens large)0,0000,000
Bibliométrie0,0000,000
Études des sciences et des technologies0,0000,000
Communication savante0,0000,000
Science ouverte0,0000,000
Intégrité de la recherche0,0000,000
Charge utile insuffisante (le modèle a refusé de juger)0,0000,000

Scores machine (provisoires)

Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.

Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.

Tête enseignante Opus0,051
Tête enseignante GPT0,232
Écart entre enseignants0,181 · la distance entre les deux têtes enseignantes sur ce seul travail
Statut de validationscore_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découle

Classification

machine, non validée

Prédiction automatique; un appel candidat d’une seule tête enseignante, pas un consensus.

Les modèles n’ont appliqué aucune catégorie : rien dans la taxonomie ne correspondait à ce travail.
Devis d'étudeSimulation ou modélisation
Domainenon disponible
GenreEmpirique

Le détail, modèle par modèle et score par score, se trouve en fin de page sous « Comment cette classification a été obtenue ».

En bref

Citations4
Publié2020
Routes d'admission1
Résumé présentoui

Explorer davantage

Même revueIADC/SPE International Drilling Conference and ExhibitionMême sujetDrilling and Well EngineeringTravaux en français237 207