Electrosynthesis of Glycerol Carbonate from Glycerol and Potassium Carbonate on Nickel Electrodes
Notice bibliographique
Résumé
The growing biodiesel industry leads to an excess production of glycerol by-product which is of low value but costly to store or dispose because glycerol is not suitable as fuel due to its sooty flame while its discharge to water leads to eutrophication. On the other hand, industrial carbon dioxide could be readily captured by scrubbing with potassium hydroxide to form potassium carbonate. With the tightening of greenhouse gas emission standards and the introduction of carbon cap and trade quota, carbon utilization becomes increasingly important both on environment and economic perspective. The combination of glycerol and carbon dioxide, in the form of dissolved carbonate ions, to produce glycerol carbonate would solve both glycerol and carbon dioxide emission problems altogether. In addition, glycerol carbonate is a valuable chemical feedstock in high industrial demand for its widespread use as solvents, surfactants, chemical feedstock and polymer materials. Compared to conventional catalysis, the electrochemical route dramatically reduces heating and pressurization requirement without using noble metal catalysts. The electrochemical synthesis of glycerol carbonate from glycerol and potassium carbonate enables utilizing electrical power to upgrade the glycerol waste into valuable glycerol carbonate while consuming carbon dioxide, under much milder conditions. The electrosynthesis of glycerol carbonate has been performed under ambient temperature and pressure on nickel plate electrodes, using potassium carbonate dissolved in glycerol with varying water dilution. The formation of glycerol carbonate was confirmed by both the characteristic peak on Cyclic Voltammetry and the Liquid Chromatography-Mass Spectrometry (LC-MS) analysis. Interestingly, comparison of LC-MS spectra with the analytical standard showed the carbonate insertion into glycerol molecule to be regiospecific, producing exclusively the more common and valuable 5-membered-ring glycerol 1,2 carbonate, instead of 6-membered-ring glycerol 1,3 carbonate. Based on this observation, it was postulated that the reaction occurred by simultaneous attack of 1,2 -OH groups of glycerol, making 1,3 bond formation impossible due to insufficient molecular “arm” length of carbonate species. LC-MS analysis revealed further C=O bond hydrogenation of glycerol 1,2 carbonate to 4-(Hydroxymethyl)-1,3-dioxolan-2-ol and dimerization of glycerol carbonate. The glycerol carbonate hydrogenation was found to be favorable under low current density such that most of glycerol carbonate formed was hydrogenated. The color change from colorless to brown of reaction mixture indicated the electrochemical dehydrogenation of glycerol to acrolein followed by subsequent polymerization to brown polyacrolein as by-product, similar to the color change observed for mixture after intense heating. Under high current density, both the polyacrolein formation and the hydrogen evolution were found to be more prevalent due to a combined effect of electrochemical polarization and local resistive heating, reducing reaction selectivity and energy efficiency. Addition of water is found to be beneficial by reducing heating requirement, resistive loss and side reactions. From the results, the novel electrochemical upgrading of glycerol waste while utilizing carbon dioxide is successfully demonstrated. However, by-product formation and energy efficiency challenges remain to be overcome for economic viability as the future “green” industrial production of valuable glycerol carbonate. While this discovery of the alternative glycerol electrochemical carbonatation has shed some light into the possible reaction mechanism, further mechanistic study is needed for better understanding of the reaction mechanism. Figure 1
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Comment cette classification a été obtenuedéplier
Prédiction distillée sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.
Scores Codex et Gemma par catégorie
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,000 | 0,002 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,001 | 0,000 |
| Bibliométrie | 0,000 | 0,000 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,001 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,000 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découleClassification
machine, non validéePrédiction automatique; un appel candidat d’une seule tête enseignante, pas un consensus.
Le détail, modèle par modèle et score par score, se trouve en fin de page sous « Comment cette classification a été obtenue ».