The Position of Bitumen Emulsions on Different Bases
Notice bibliographique
Résumé
Fast and durable repair of asphalt roads is important for a functioning infrastructure.An important method is the milling of the old asphalt layer in order to place a new layer on top ("hot on cold" paving).A bitumen emulsion is used as an adhesion primer.The adhesion of the materials due to the emulsion at the layer boundary is intended to improve the bond and thus dissipate the stresses that occur due to traffic loading [1]- [3].For this purpose, it is necessary to choose the correct quantity of spray [4]-[5] and to distribute it uniformly.Bitumen emulsion consists of bitumen, water and an emulsifier.The emulsifier causes the fine bitumen droplets to spread in a stable state in the water [6].After spraying, the bitumen emulsion breaks and the water evaporates [7].To determine the location of bitumen emulsion in this study, a C40 B5-S (40-wt.%content of bitumen) was sprayed onto the different bases using a specially designed spray-on system (spray-on quantities: 225 g/m 2 ; 450 g/m 2 ).The surfaces of the two variants differ in the texture of the surface and in the void content on the surface (dense surface (milled); open-pore surface (asphalt texture)).The aim of this study was to determine the position of bitumen emulsion on theses surfaces using the X-ray computed micro tomography (-CT) technique.Tis technique allows 3D imaging of structures by measuring different densities [8].For the analysis of the thin layers of the bitumen emulsion, a highdensity tracer (barium sulfate) was added, which had no interfering effect on the viscosity of the bitumen emulsion.This made it possible to identify the bitumen emulsion in the subsequent analysis due to the difference in density.[9].The (sprayed) samples were measured using a high-resolution -CT (type: Zeiss Xradia 520 Versa).The measurements were performed with a voltage of 140 kV and a power of 10 watts.The spatial resolution was 34.5 m.The results of the measurements with the -CT showed that the distribution of the bitumen emulsion on a milled surface is uneven.In the deepening's of the structure, an emulsion thickness of 917 m could be measured.Further there was only a small amount of bitumen emulsion on the crests and slopes compared to the deepening's (measured thickness: 217 m).For the samples with the asphalt surface the bitumen emulsion flows into the voids and was collected there.Almost no emulsion was detected at the actual layer boundary.From the results it can be concluded that the distribution is not optimal and thus no optimal bonding is achieved.For this reason, in further studies the bitumen emulsion will be adjusted in terms of viscosity to achieve a more uniform distribution.This study showed that a new understanding of the material can be obtained with 3D imaging, allowing optimization steps to be applied that lead to better material behavior.
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Comment cette classification a été obtenuedéplier
Prédiction distillée sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.
Scores Codex et Gemma par catégorie
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,000 | 0,000 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,000 | 0,000 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,000 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,000 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découleClassification
machine, non validéePrédiction automatique; un appel candidat d’une seule tête enseignante, pas un consensus.
Le détail, modèle par modèle et score par score, se trouve en fin de page sous « Comment cette classification a été obtenue ».