The Increasing of the Heat Transfer Coefficient of Short Linear Heat Pipes
Pourquoi ce travail est dans la base
Une base qui oublie comment elle a trouvé un travail ne peut pas être vérifiée. Voici les voies qui ont admis celui-ci.
Notice bibliographique
Résumé
The results of the experimental studies of heat transfer coefficients K<SUB>HP</SUB> of short linear heat pipes (HP’s) with a Laval nozzle-liked vapour channel, and with a partially swirled vapour flow inside the channel are presented. A partial azimuthal swirling of the jet vapour stream is created using inclined injection channels 1 mm in diameter in a flat multilayer mech evaporator, with an inclination angle φ relative to the longitudinal axis in the azimuthal direction, in the range of 0° < φ < 60°. The heat transfer coefficients K<SUB>HP </SUB>of a set of the identical HP’s with a different inclination angles φ of the injection channels in the evaporators, with the same working fluid mass filling (δm/m ≤ 0.1 %), at the same evaporator temperature heat load δT = T<sub>ev</sub> –T<SUB>B</SUB> = (20 ± 0.03) K, represent an extreme convex function, depending on the inclination angle φ magnitude of the injection channels, with a maximum at the swirled angle of the vapour flow φ = 26° ± 2°. The magnitude of the excess of the K<SUB>HP </SUB>with a swirling vapour flow over the identical HP’s with a direct vapour flow reaches 10%. An analysis of the recommended vapour channel shape, carried out by the estimating of the Richardson number Ri of the vapour flow jets above the evaporator, allowed us to estimate the value of the dimensionless longitudinal radius of curvature δ/R<sub>conf</sub> of the confuser part of the vapour channel, which is determined from the condition of minimal friction losses during the flow of moist vapour in the boundary layer δ along the concave wall of the confuser part of the vapour channel with a longitudinal radius of curvature R<sub>conf</sub>. The concave diffuser part shape of the vapour channel is determined by the condition that the moving vapour jets velocity vectors must be parallel to the longitudinal axis of the diffuser part of the HP’s vapour channel. The results of the numerical simulation of the hydraulic resistance coefficients ξ<sub>vp</sub> of the HP’s vapour channel, closed with flat covers, with partially swirling jet vapour flow, obtained by using the ANSYS FLUENT program, show a decrease in ξ<sub>vp</sub> coefficients at high values of the evaporator temperature load, in the range of vapour flow velocities 1 m/s < u<sub>z</sub> ≤ 100 m /s, and in the range of swirling angles 0°<φ<30°. With the increasing the swirling angles φ>30°, a sharp increase in the hydraulic resistance coefficient ξ<sub>vp</sub> begins.
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Prédiction distillée sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.
Scores Codex et Gemma par catégorie
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,000 | 0,000 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,000 | 0,001 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,000 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,000 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découle