Milling characteristics of SiCp/2024Al composites thin-walled part based on movable auxiliary support
Notice bibliographique
Résumé
Due to milling force and milling heat, thin-walled parts are highly susceptible to deformation and even scrap. In this paper, a method of milling thin-walled part based on the movable auxiliary support was proposed. The ABAQUS software was employed to simulate the milling of thin-walled SiCp/2024Al composite part, while the movement of the auxiliary support was simulated using the secondary development subroutine VDLOAD. The influences of the magnitude and area of the movable auxiliary support on the surface temperature, deformation, and residual stress of the workpiece were investigated by single factor method. The results showed that, with the increasing of the magnitude and area of the movable auxiliary support, both surface temperature and deformation of the thin-walled part decrease. The tensile residual stress decreases and gradually changes to compressive residual stress. Interestingly, when the magnitude exceeds 20 MPa or the area exceeds 100 mm 2 , the deformation of the thin-walled part continues to decrease, but the middle of the thin-walled part is concave toward the milling cutter. It is worth noting that the effect of area on the residual stress does not show a clear regularity. Thus, the reasonable auxiliary support can reduce deformation and stability in the milling of thin-walled parts and the results of the study can provide a theoretical basis for optimizing the milling process of thin-walled parts.
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Comment cette classification a été obtenuedéplier
Prédiction distillée sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.
Scores Codex et Gemma par catégorie
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,000 | 0,000 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,000 | 0,000 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,000 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,000 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découleClassification
machine, non validéePrédiction automatique; un appel candidat d’une seule tête enseignante, pas un consensus.
Le détail, modèle par modèle et score par score, se trouve en fin de page sous « Comment cette classification a été obtenue ».