Influence of Composition and Processing Methods on the Microstructure and Properties of Co-Cr-Fe-Mn-Ni High Entropy Alloys
Notice bibliographique
Résumé
This research was undertaken to evaluate potential use of high entropy alloys (HEAs) for high-temperature gas turbine applications.The microstructure and properties of three HEAs -CoCrFeMnNi, Al0.5CoCrFeMnNi1.5, and Al0.5CoCrFeNi1.5 -were examined to assess the impact of Mn and Al additions and the effect of heat treatments on the microstructure and the mechanical properties.In addition, preliminary process development of manufacturing one of the alloys using a laser based additive manufacturing (AM) method was also conducted.The results showed that Al addition resulted in hardness increase due to the formation of FCC-L12 Ni3Al and BCC-B2 NiAl phases, while Mn addition enhanced the hardness at the expense of lowering phase stability temperature and solidus temperature.The AM process development, based on a laser powder direct energy deposition (LP-DED) system, showed that laser power, scanning speed, and material feed rate all had significant impact on resulted sample height and width.Finally, the comparative analyses of CoCrFeMnNi HEAs, processed through casting (hot isostatic pressed in the as-received condition), hot isostatic pressing (HIP) of powder material, and LP-DED, revealed that sintering by HIP resulted in superior density and reduced defects in the material.Tensile testing of LP-DED-fabricated CoCrFeMnNi revealed minimal differences in strength along two deposition orientations, while reduced ductility was observed along the transverse orientation.This study concluded that the alloy composition, manufacturing techniques, and heat treatment all resulted in microstructure changes, hence subsequent impact on the performance.Chapter 3: outlines the methods employed for material preparation and the experimental approaches adapted to study the impact of process parameters on DED additive manufacturing.Additionally, it details the procedures for sample preparation and the characterization methods employed.Chapter 4: presents the results and discussion of this research.This section is further divided into three subsections based on publications: Chapter 4.1: Evaluation of the Impact of Mn and Al on the Microstructure of Fe-Co-Ni-Cr Based High Entropy Alloys Chapter 4.2: Microstructure and Properties of Co-Cr-Fe-Mn-Ni Based High Entropy Alloys with Al Addition Through Heat Treatments Chapter 4.3: Microstructures and Properties of HEA Fabricated by Different Manufacturing Methods Chapter 5: presents a summary of the findings from this research.
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Comment cette classification a été obtenuedéplier
Prédiction distillée sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Apprise à partir de 10 348 étiquettes directes de Codex et de 10 348 étiquettes directes de Gemma. Le mode candidate est l'union des têtes enseignantes seuillées; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont ni des étiquettes humaines ni des étiquettes directes de modèles de pointe.
Scores Codex et Gemma par catégorie
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,000 | 0,000 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,000 | 0,000 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,000 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,000 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,000 | 0,000 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découleClassification
machine, non validéePrédiction automatique; un appel candidat d’une seule tête enseignante, pas un consensus.
Le détail, modèle par modèle et score par score, se trouve en fin de page sous « Comment cette classification a été obtenue ».