DLFT experiments with cyclic butylene terephtalate
Notice bibliographique
Résumé
Cyclic oligomers have low molecular weights and therefore exhibit very low viscosities (in the order of 20 mPa.s) in contrast to the resulting high viscosities related to high molecular weightsobtained after polymerization. This characteristic is very appealing for the production of polymer composites since by taking advantage of the low viscosity, fibres can be thoroughly wetted by the cyclic oligomer before starting the reactive process of polymerization. As a result, a homogeneous mixture with a uniform volumetric distribution of reinforcing fibres in the polymer matrix is expected with the use of appropriate processing equipment. Cyclic butylene terephthalate (CBT®) has been successfully polymerized into poly(butylene terephthalate) (PBT) using a variety of tin or titanate-based initiators. An exploratory project has been initiated by NRC at the Magna-NRC Composites Centre of Excellence (MNCCE) with the participation of Cyclics Corporation (Cyclics) as the supplier of CBT for trials using the D-LFT process. The goal is to assess a number of aspects involved in the simultaneous reactive extrusion/compounding process using CBT fibreglass reinforcement in a D-LFT process in order to determine the adequate processing conditions to produce parts. This paper presents a description of the experiments conducted up to date and the results obtained thereby. Parts were produced using a test specimen mould with a shot-pot device and a storage tub for automotive applications. Samples were characterized for tensile, flexural and impact tests. Density measurements were taken at different points of the tub to examine the uniformity of the composite material obtained. Plaques moulded with the test specimen mould showed good mechanical properties which exceed typical values for PP with 40% glass composites. The experiments proved the feasibility of the use of the open ring polymerization process in a D-LFT system. A set of operating conditions including temperature profile, screw speed and feed rate was established to achieve the adequate residence time and material temperature history for the effective processing of CBT in the D-LFT system.Mechanical properties measured from the moulded part (tub) showed significantly lower values than those for the test specimen mould. These were related to incomplete packing of the material in the cavity of the mould, the high residence time required and non-optimal shot size.High variability within the parts and between parts produced is thought to be a consequence of the processing difficulties for the tub mould.
Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.
Comment cette classification a été obtenuedéplier
Prédiction machine sur la base complète
Imitation des enseignantsNi prévalence calibrée, ni vérité terrain. Validation humaine à venir. Le volet Gemma est une étiquette directe du modèle pour chaque travail de la base, lue sur la notice réduite au titre. Le volet Codex est un classifieur appris des 10 348 étiquettes directes de Codex et calibré sur les taux pondérés de l'échantillon; les champs sans appui suffisant ne portent aucun appel Codex. Le mode candidate est l'union des deux volets; le consensus est leur intersection. Ces sorties portent le statut machine_predicted_unvalidated et ne sont pas des étiquettes humaines.
Scores du classifieur distillé par catégorie (deux têtes)
| Catégorie | Codex | Gemma |
|---|---|---|
| Métarecherche | 0,000 | 0,000 |
| Méta-épidémiologie (sens strict) | 0,000 | 0,000 |
| Méta-épidémiologie (sens large) | 0,000 | 0,000 |
| Bibliométrie | 0,000 | 0,001 |
| Études des sciences et des technologies | 0,000 | 0,000 |
| Communication savante | 0,000 | 0,000 |
| Science ouverte | 0,000 | 0,000 |
| Intégrité de la recherche | 0,000 | 0,001 |
| Charge utile insuffisante (le modèle a refusé de juger) | 0,004 | 0,001 |
Scores machine (provisoires)
Les deux têtes enseignantes du modèle étudiant, lues sur ce travail. Un score ordonne la base pour la relecture; il n'affirme jamais une catégorie, et le statut de validation accompagne chaque rangée tel quel.
Scores de référence d'un modèle non mature (critères de maturité non atteints, 7 itérations). Un score ordonne; il n'affirme jamais une catégorie.
score_only:v0-immature-baseline · tel quel depuis la passe de notation : score_only signifie que le nombre peut ordonner les travaux, et qu'aucune étiquette de catégorie n'en découleClassification
machine, non validéePrédiction automatique; un appel candidat d’une seule source (Gemma direct ou Codex distillé), pas un consensus.
Le détail, modèle par modèle et score par score, se trouve en fin de page sous « Comment cette classification a été obtenue ».