Recycled Aggregate Concrete: A Comparative Analysis of Environmental Impact and Performance

Abstract The global construction industry is a primary consumer of natural resources and a significant generator of construction and demolition (C&D) waste. Recycled Aggregate Concrete (RAC), produced by replacing conventional natural aggregates (NA) with crushed concrete debris, has emerged as a paramount sustainable solution to mitigate the dual crises of natural resource depletion and landfill overcrowding. This article presents an extensive comparative analysis of the mechanical performance, microstructural characteristics, and environmental impacts of RAC versus conventional Natural Aggregate Concrete (NAC). Through a comprehensive review of experimental studies conducted up to 2019, it is observed that while RAC often exhibits lower compressive strength and higher water absorption due to the porous nature of adhered mortar, these deleterious effects can be systematically managed through optimized mix design, the use of chemical and mineral admixtures, and rigorous partial replacement strategies. Life cycle assessments (LCA) consistently confirm that the large-scale adoption of RAC significantly reduces the total carbon footprint, cumulative energy demand, and environmental toxicity associated with the extraction and long-haul transportation of virgin aggregates. Furthermore, this study examines the economic landscape, arguing that regulatory frameworks, standardized certification processes, and the development of localized recycling hubs are essential for the commercial viability of RAC in structural applications. By bridging the gap between laboratory-scale research and real-world construction demands, this study outlines a pathway toward a more resilient and circular built environment, emphasizing the transition from linear consumption to a closed-loop regenerative system. Keywords: Recycled Aggregate Concrete (RAC), Natural Aggregate Concrete (NAC), Sustainable Construction, Mechanical Properties, Microstructure, Environmental Impact, Life Cycle Assessment (LCA), Circular Economy. 1. Introduction Global urbanization has escalated the demand for infrastructure development at an unprecedented pace, leading to unsustainable rates of natural resource extraction and the degradation of quarry sites. Concrete, being the most widely used anthropogenic construction material on Earth, relies heavily on the consumption of virgin coarse and fine aggregates. Simultaneously, the rapid growth of cities and the subsequent demolition of aging infrastructure generate millions of tons of C&D waste annually, which often occupy valuable landfill space. Recycled Aggregate Concrete (RAC) presents a robust circular economy approach, repurposing demolition debris as raw material for new concrete production. By transitioning from a "take-make-dispose" model to a regenerative cycle, the industry can significantly reduce its reliance on primary stone sources. This article explores the technical feasibility, economic implications, and the broader ecological benefits of integrating recycled concrete aggregate (RCA) into structural and non-structural applications. As the industry faces mounting pressure to meet net-zero carbon targets, RAC stands out as a critical tool for reducing embodied energy in the built environment. Beyond the immediate sustainability benefits, this shift also addresses the looming scarcity of high-quality natural sand and gravel in major metropolitan hubs, where the cost of logistics is increasingly becoming a prohibitive factor for traditional concrete production. Furthermore, the integration of RCA supports the development of "urban mining," a practice that treats existing building stock as future resources rather than waste, fundamentally changing the logistical footprint of the construction supply chain. This paradigm shift is not merely an engineering convenience but a socio-economic necessity. As natural quarry reserves face depletion and the ecological cost of sand extraction (especially marine sand) rises, the construction sector must reconcile its growth with the planetary boundaries of material consumption. RAC provides the flexibility to transform our built environment into a repository of high-value raw materials, ensuring that today's infrastructure supports the resources required for tomorrow’s development. This transition is further catalyzed by the rising costs of traditional waste disposal, where landfill tipping fees are increasingly pricing out linear disposal models, making the recovery of aggregates a financially superior strategic choice for municipal planners and private developers alike. 2. Material Characteristics and Microstructure Recycled Concrete Aggregate (RCA) differs fundamentally from natural aggregate due to the presence of residual, old cement mortar adhered to the original aggregate surface. This adhered mortar layer creates a complex, multi-phase microstructure that dictates the macroscopic performance of the concrete. Porosity and Water Absorption: The residual mortar is intrinsically more porous than the parent natural stone. Consequently, RCA possesses a significantly higher water absorption capacity—often 3% to 10% by mass—compared to the 0.5% to 2% typically seen in natural aggregates. This high absorption makes the design of effective water-cement ratios challenging, as the aggregate tends to compete with the cement paste for mixing water. If not accounted for in mix design, this leads to an increase in the effective water-cement ratio, which paradoxically compromises the strength of the new matrix. To combat this, engineers must employ pre-saturation techniques or adjust mix proportions to ensure that the aggregate does not inadvertently "starve" the hydration process of the surrounding cement paste. The porous nature of the RCA effectively creates an internal reservoir that can contribute to autogenous curing but requires sophisticated mix adjustments to avoid detrimental drops in early-age strength. Extensive research into moisture management during batching indicates that pre-wetting the aggregates to a saturated surface-dry (SSD) state is the most reliable method to ensure consistent workability without sacrificing long-term mechanical performance. Without such precision, the rapid water uptake can lead to premature drying shrinkage and internal micro-cracking during the setting phase, which subsequently impacts the long-term impermeability of the concrete. Density and Specific Gravity: Due to the lighter density of the adhered mortar, the overall specific gravity of RCA is typically 5% to 15% lower than natural stone. This lower density also results in a higher yield per ton of aggregate, which, while beneficial for logistical planning, must be accounted for in volume-based concrete batching. The discrepancy in density also influences the dynamic response of structural components, which must be considered in seismic design where mass properties are key. Engineers must adjust the structural design calculations to account for this lighter self-weight, potentially leading to more efficient structural frames that reduce the load on foundations. Moreover, the lower density influences aggregate segregation during casting, requiring careful vibration control during placement to prevent the mortar and aggregate from separating under gravity. This necessitates a more refined vibration regime on-site to ensure the RCA stays uniformly suspended in the fresh mix, preventing localized pockets of weaker, mortar-rich zones. Interfacial Transition Zone (ITZ): In RAC, there exist two types of ITZs: the original bond between the aggregate and old mortar, and the new bond between the RCA and the new mortar matrix. This double-layer interface is often identified as the "weak link" that contributes to performance reductions under mechanical stress. The presence of micro-cracks in the adhered mortar, originating from the initial demolition process, further creates stress concentrations that propagate when the new concrete is loaded. Advanced microscopic analysis reveals that the ITZ in RAC is more porous than in NAC, necessitating the use of supplementary cementitious materials (SCMs) like silica fume or fly ash to densify these regions and improve interfacial bonding. The use of nano-materials, such as nano-silica, has shown significant potential in chemically bonding the old mortar to the new matrix, essentially creating a "healed" ITZ that approaches the homogeneity of natural aggregates. This healing process is critical for high-strength applications where the ITZ often dictates the failure mode of the concrete sample under compression or tensile splitting tests. Beyond just filling voids, these nano-scale interventions act as nucleation sites for C-S-H gel development, significantly refining the pore structure and improving the transition from the matrix to the aggregate core. 3. Mechanical Performance Analysis Numerous longitudinal studies (e.g., Limbachiya et al., 2000; Venu & Ramesh, 2015) have demonstrated that the quality of the parent concrete significantly dictates the performance of the resulting RAC. Compressive Strength: RAC typically shows a reduction in compressive strength of 5% to 25% compared to NAC, depending on the percentage of replacement and the strength of the parent concrete. Higher levels of replacement (exceeding 30%) generally necessitate compensatory measures to ensure structural integrity, such as lowering the water-cement ratio or utilizing high-range water reducers. It is observed that when the source of RCA is high-strength structural concrete, the degradation in compressive strength is minimized, whereas RCA derived from low-strength non-structural debris leads to more pronounced strength reductions. This highlights the importance of source-separated C&D waste streams, where higher-quality concrete is reserved for structural applications while lower-quality debris is diverted to road base or landscaping. The variab

Récupéré en direct depuis OpenAlex et désinversé. Les résumés ne sont pas conservés dans cette base de données : les index inversés représentent 8,6 Go des 9,3 Go de texte de la base, et le serveur dispose de 13 Go libres.