Physical Properties of Carbon Fiber Doped Micropatternable Nanocomposite Polymer
Why this work is in the frame
A frame that forgets how it found something cannot be audited. These are the routes that admitted this work.
Bibliographic record
Abstract
We present the preparation and characterization of conductive hybrid polymer by blending carbon fibers into polydimethylsiloxane (PDMS) [1, 2] for various application such as wearable devices, MEMS, soft robotics, sensors, actuators and microfluidics. Here, we compared the conductivity of hybrid polymer and effect of different length of fibers with variant weight percentage (wt%). Fibers length of 50μm, 150μm and 250μm were doped in uncured PDMS matrix and sample size of 1cm X 2cm were fabricated using heat press for 10, 15, 25, 30, 40, 50 and 60 wt%. Percolation threshold for the hybrid polymer was observed at 50 wt%. Conductivity at 50wt% fibers of 250μm, 150μm and 50μm dimensions were 19047.619 S/m, 4347.82 S/m and 307.69 S/m respectively, which showed the influence of the higher dimensions (i.e., length) with more crosslinking of the fibers.The electrical conductivity was measured using a 4 point probe set up as previously reported by authors [3, 4, 5] Further, SEM images showed (Fig 4) the uniform dispersion of the fibers in the PDMS matrix. Mechanical characteristics such as elastic modulus (Ε’) and loss modulus (E’’) were measured for PDMS and different percentage of fibers doped in PDMS using dynamic mechanical analysis (Q800 DMA by TA instruments). We observed a decrease in the elastic modulus of PDMS at 50 ̊C due to the amorphous structure. Whereas, the hybrid polymer showed the decrease at 100 ̊C as shown in Figs. 2 and 3. It was observed that in the same condition increase in the weight percentage of the filler (carbon fibers of 150μm length) there was increase in elastic moduli. The rubbery state of the polymer showed higher magnitude in modulus value (hybrid polymer 36MPa whereas PDMS 11MPa). It is also observed that with an increase in weight percentage of carbon fibers in PDMS polymer matrix, results in increased elastic response. The prepared nanocomposite was micromolded against a 3D printed (Fig. 5) mold as previously published by the authors [6, 7, 8, 9]. References: A. Khosla, B.L. Gray, Preparation, characterization and micromolding of multi-walled carbon nanotube polydimethylsiloxane conducting nanocomposite polymer, Materials Letters, Volume 63, Issues 13–14, 31 May 2009, Pages 1203-1206, ISSN 0167-577X, http://doi.org/10.1016/j.matlet.2009.02.043 Khosla, A. and Gray, B. L. (2010), Preparation, Micro-Patterning and Electrical Characterization of Functionalized Carbon-Nanotube Polydimethylsiloxane Nanocomposite Polymer. Macromol. Symp., 297: 210–218. doi:10.1002/masy.200900165 Khosla, Ajit, and Bonnie L. Gray. "(Invited) Micropatternable Multifunctional Nanocomposite Polymers for Flexible Soft NEMS and MEMS Applications." ECS Transactions 45.3 (2012): 477-494. doi: 10.1149/1.3700913 A. Khosla ; B. L. Gray; Fabrication of multiwalled carbon nanotube polydimethylsiloxne nanocomposite polymer flexible microelectrodes for microfluidics and MEMS. Proc. SPIE 7642, Electroactive Polymer Actuators and Devices (EAPAD) 2010, 76421V (April 09, 2010); doi:10.1117/12.847292. A. Khosla ; B. L. Gray; Fabrication and properties of conductive micromoldable thermosetting polymer for electronic routing in highly flexible microfluidic systems. Proc. SPIE 7593, Microfluidics, BioMEMS, and Medical Microsystems VIII, 759314 (February 17, 2010); doi:10.1117/12.840911. Khosla, A. (2011). Micropatternable multifunctional nanocomposite polymers for flexible soft MEMS applications(Doctoral dissertation, Applied Science: School of Engineering Science). http://summit.sfu.ca/item/12017 Khosla, A. (2012). Nanoparticle-doped electrically-conducting polymers for flexible nano-micro Systems. The Electrochemical Society Interface, 21(3-4), 67-70. doi: 10.1149/2.F04123-4if Gray, B. L., & Khosla, A. (2010). Microfabrication and applications of nanoparticle doped conductive polymers. Nanoelectronics: Nanowires, Molecular Electronics, and Nanodevices, 227. Ozhikandathil, Jayan, Ajit Khosla, and Muthukumaran Packirisamy. "Electrically Conducting PDMS Nanocomposite Using In Situ Reduction of Gold Nanostructures and Mechanical Stimulation of Carbon Nanotubes and Silver Nanoparticles." ECS Journal of Solid State Science and Technology 4.10 (2015): S3048-S3052. doi: 10.1149/2.0091510jss Figure 1
Fetched live from OpenAlex and de-inverted. Abstracts are not stored in this database: the inverted indexes are 8.6 GB of the frame’s 9.3 GB of text, and the host has 13 GB free.
Full frame distilled prediction
Teacher imitationNot calibrated prevalence, not ground truth. Human validation pending. Learned from the 10,348 direct Codex labels and 10,348 direct Gemma labels. Candidate is the union of thresholded teacher heads; consensus is their intersection. These outputs are machine_predicted_unvalidated and are not human labels or direct frontier model labels.
Codex and Gemma teacher scores by category
| Category | Codex | Gemma |
|---|---|---|
| Metaresearch | 0.000 | 0.000 |
| Meta-epidemiology (narrow) | 0.000 | 0.000 |
| Meta-epidemiology (broad) | 0.000 | 0.000 |
| Bibliometrics | 0.000 | 0.000 |
| Science and technology studies | 0.000 | 0.000 |
| Scholarly communication | 0.000 | 0.000 |
| Open science | 0.000 | 0.000 |
| Research integrity | 0.000 | 0.000 |
| Insufficient payload (model declined to judge) | 0.000 | 0.000 |
Machine scores (provisional)
The two teacher heads of the student model, read on this work. A score orders the frame for review; it never asserts a category, and the validation status ships verbatim with every row.
Baseline scores from an immature model (maturity gate not passed, 7 training rounds). Scores rank; they never assert a category.
score_only:v0-immature-baseline · verbatim from the scoring run: score_only means the number may rank works, and no category label ships from it